This Episode's Questions
Guy's Questions
Hey, fellas. Great show. I’ve been listening for a couple of years, and have really elevated my game based on tips from y’all. Guy, thanks for the Incra TS/LS videos. I got the combo version when I moved my router table to the wing of my Sawstop. I really love it. I have a follow up question from the Feb 24 edition: Guy, you were pretty emphatic on your answer regarding connecting 2 Festool rails. I’m curious to know if your opinion was formed on the original style or the new version? If the former, have you had a chance to play with the new ones. I replaced my old set with the self-adjusting version and they seem rock-solid to me. I leave a small gap between the rails in case the rails aren’t exactly 90 degrees. I’m also careful when moving the joined rail from one sheet to another that I don’t torque the joint. Just wondering which version your judgement was associate with? Pat Engel
Hi guys! My name is Elisa and I’m new to woodworking. I have a few fairly straightforward projects under my belt including a crate topper to go on top of my dog’s crate, a few blanket ladders, and a mobile workbench with a spot for my Ryobi 8 1/4 table saw.
I’m working on box joints right now. I’ve watched a ton of videos and made a lot of sawdust trying to make a jig and have been unsuccessful. I’m using a single blade with a kerf of .0665 in but I can measure the blade and make several cuts and not get the same measurement between them all, so there’s one problem. I’m trying to set the spacing up to be 1/2 inch but I can’t seem to get it right. The distance I’m off is small but bringing my pin closer or further from the blade seems to change the width of the pins and the slots and I can’t see a correlation between the changes that would help me figure out how to correct it.
In addition to the Ryobi saw, I have been using a sled I made, digital calipers, clamps, a set of steel thickness gauges. I’m using a variety of test piece’s including 3/4 in plywood, 3/8 and 1/2 inch S4S poplar and pine. If it helps to know, I have a miter saw, jig saw, a trim router, a regular size router, cordless drill and driver and basic hand tools.
I’d appreciate any help you can offer and if you can recommend some really good YouTube videos!
Thanks! Elisa Gonzales
Hello all. I have a veneering question. I want to wrap a elliptical cylinder with walnut veneer. It measures 18” inches long and 16” tall with end radiuses that are 4” round.  The cylinder is made with stacked mdf each layer is cut in the elliptical shape and stacked to my desired height. I don’t have a vacuum press.  mdf is notorious for absorbing solvents and water. I’ve ruled out PSA backed veneer since this will be adhered to the cut edges of mdf and most likely would peel away. I am thinking maybe 2 coats of solvent based contact cement on the mdf and one coat on the veneer.  I need an adhesive that will hold those radial ends. Do you think contact cement will be strong enough and if so good recomm ndations?  Also should I seal the mdf  before applying the adhesive?  Maybe with shellac or WB poly. I’d say lacquer but concerned the solvent in the cement would have a negative effect on the lacquer seal coat.  Veneer hammer? Jeff (Maker)
Huy's Questions:
Gentlemen-
 Sorry to not have rapped at ya in a while, winter is for snowboarding, and I tend to loose the plot in the shop. But whilst schussing down the slopes, I have been contemplating spring projects, namely, a bridge for my stream/river. The "slash" is because it is usually a stream, but two or three times a year gets very rowdy; the last time it washed the existing 16' long bridge off its moorings 90º, so it now sits parallel to the stream instead of across it. This bridge was made of pressure treated 2x12's, 4' wide, heavy, and chained to pins in boulders, so the water has some force when she's angry.
 Instead of trying to lever and pulley the bridge back into place, let's build a new one. You guys know I